DutchWest DW2500X02 Owner's Manual download pdf (Page 9)

DW2500X02

30004581



  

  

Low Fully Closed 9,500

Med / High 1/2” (13 mm) Open 16,315

High Fully Open 58,000



     









The following use and safety tips should be observed.

1. Inspect the glass regularly for cracks and breaks. If

you detect a crack or break, extinguish the fire im-

mediately and contact your dealer for replacement.

2. Do not slam door or otherwise impact the glass.

When closing doors, make sure that logs or other

objects do not protrude and impact the glass.

3. Do not clean the glass with materials which may

scratch (or otherwise damage) the glass. Scratches

on the glass can develop into cracks or breaks.

4. Never attempt to clean the glass while unit is hot. If

the deposit is not very heavy, normal glass clean-

ers are adequate with a plain, nonabrasive scouring

pad. Heavier deposits may be removed with the use

of a readily available oven cleaner.

5. Never put substances which can ignite explosively

in the unit since even small explosions in confined

areas can blow out the glass.

6. This unit has an airwash system, designed to reduce

deposits on glass.







After extensive use, the sealing material which provides

glass and door seal may need to be replaced if it fails

to sustain its resilience. Inspect glass and door seal pe-

riodically to ensure for proper seal. If gaskets become

frayed or worn, replace immediately.

Contact your dealer for approved replacement parts.

The following steps should be followed for glass gasket

replacement:

1. Ensure appliance is not in operation and has thor-

oughly cooled.

2. Remove screw and glass clip.

3. Lift glass out from glass clip.

4. Remove old gasket and clean glass.

5. Replace new gasket starting at the bottom of glass

working along edges, being sure to center gasket

channel on glass.

6. Trim to length and butt ends together.

7. Replace glass in door, being sure not to over-tighten

screw and clip.

It is normal to see flat spots on painted surfaces of the

stove. The flat spots on the paint surface indicate the

hotter surfaces of the stove, and is caused by the heat

radiating through the paint. It is also expected that shiny

spots caused by friction from the packaging materials,

will disappear during the curing of the stove.

SO:

1. Remember to ventilate well.

2. Allow the stove to cure before burning for long peri-

ods at high temperatures.

3. Flat spots on the painted surfaces are normal.

4. Shiny spots on the paint surface before burning is

normal.

5. Call your dealer if you have any questions.



1. Open inlet air control fully.

2. Place a small amount of crumpled paper in the

stove.

3. Cover the paper with a generous amount of kindling

in a teepee fashion and a few small pieces of wood.

4. Ignite the paper and close door. If fire dies down

substantially, open door slightly.

5. Add larger pieces of wood as the fire progresses be-

ing careful not to overload. Do not fill firebox beyond

firebrick area. An ideal coal bed of 1” to 2” should be

established to achieve optimum performance.

6. This unit is designed to function most effectively

when air is allowed to circulate to all areas of the

firebox. An ideal means of achieving this is to rake a

slight (1” to 2” wide) trough in the center of the coal

bed from front to back prior to loading the fuel.

7. Once fuel has been loaded, close the door and open

air inlet control fully until fire is well established (ap-

prox. 10 minutes) being careful not to overfire.

8. Readjust air inlet control to desired burn rate. If

excessive smoke fills firebox, open air inlet control

slightly until flames resume and wood is sufficiently

ignited. While a basic rule of thumb is “closed-low”,

“1/2 way - medium” and “fully open-high”, refer to the

Inlet Air Control Settings chart.

9. When refueling, adjust air control to the fully open

position. When fire brightens, slowly and carefully

open the door. This procedure will prevent gases

from igniting causing smoke and flame spillage.

10.Add fuel being careful not to overload.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 31 32

Comments to this Manuals

No comments

DutchWest DW2500X02 Owner's Manual Page 9

Comments to this Manuals

Related products and manuals for Stoves DutchWest DW2500X02